Summary

Summary
In this chapter-1,
 You learned about the items that can be found on a typical network. 
You first learned what a network is and the various elements that make up a network, such as servers, workstations, and hosts.
Then you learned about the different ways of laying out a network.
 You learned about bus, star, ring, mesh, and hybrid topologies.
 You also learned about the different types of physical media in use on networks today, including coaxial, twisted-pair, and fiber-optic media. Finally,
 you learned about some common network devices—including NICs, hubs, switches, bridges, routers, and gateways—seen on a typical network.

Thanks for the follow-up

Read More

Other Devices

Other Devices
In addition to these network connectivity devices, there are several devices that, while maybe not directly connected to a network, participate in moving network data:

• Modems
• ISDN terminal adapters
• Wireless access points
• CSU/DSUs
• Transceivers (media converters)
• Firewalls

Modems
A modem is a device that modulates digital data onto an analog carrier for transmission over an analog medium and then demodulates from the analog carrier to a digital signal again at the
receiving end. The term modem is actually an acronym that stands for MOdulator/DEModulator. When we hear the term modem, three different types should come to mind:

• Traditional (POTS)
• DSL
• Cable
• 
  

Traditional (POTS)
Most modems you find in computers today fall into the category of traditional modems. These modems convert the signals from your computer into signals that travel over the plain old telephone
service (POTS) lines. The majority of modems that exist today are POTS modems, mainly because PC manufacturers include one with a computer.

DSL
Digital subscriber line (DSL) is quickly replacing traditional modem access because it offers higher data rates for a reasonable cost. In addition, you can make regular phone calls while online. DSL
uses higher frequencies (above 3200Hz) than regular voice phone calls use, which provides greater bandwidth (up to several megabits per second) than regular POTS modems provide while still
allowing the standard voice frequency range to travel at its normal frequency to remain compatible with traditional POTS phones and devices, an advantage over ISDN. DSL “modems” are the
devices that allow the network signals to pass over phone lines at these higher frequencies. Most often, when you sign up for DSL service, the company you sign up with will send you
a DSL modem for free or for a very low cost. This modem is usually an external modem (although internal DSL modems are available), and it usually has both a phone line and an Ethernet connection. You must connect the phone line to a wall jack and the Ethernet connection to your computer (you must have an Ethernet NIC in your computer in order to connect to the DSL modem). Alternatively, a router, hub, or switch may be connected to the Ethernet port of the DSL modem, increasing the options available for the Ethernet network.

Note:

If you have DSL service on the same phone line you use to make voice calls, youmust install DSL filters on all the phone jacks where you have a phone. Or, a DSL filter will be installed after the DSL modem for all the phones in a building. Otherwise,you will hear a very annoying hissing noise (the DSL signals) on your voice calls.

Cable
Another high-speed Internet access technology that is seeing widespread use is cable modem access. Cable modems connect an individual PC or network to the Internet using your cable television
cable. The cable TV companies use their existing cable infrastructure to deliver data services on unused frequency bands.
The cable modem itself is a fairly simple device. It has a standard coax connector on the back as well as an Ethernet port. You can connect one PC to a cable modem (the PC will need to have an Ethernet NIC installed), or you can connect the modem to multiple PCs on a network (using a hub or switch). A router may also be used to enhance the Ethernet network’s capabilities.


ISDN Terminal Adapters
Integrated Services Digital Network (ISDN) is another form of high-speed Internet access. It delivers digital services (over 64Kbps channels) over conditioned telephone copper pairs. The
device you must hook up to your computer to access ISDN services is properly known as an ISDN Terminal Adapter. It’s not a modem in the truest sense of the word because a modem changes from digital to analog for transmission. An ISDN TA doesn’t change from digital to analog. It just changes between digital transmission formats. The box itself is about the size of a modem and looks similar to one. But, as with DSL modems, there is a phone jack and an Ethernet jack. You connect a phone cord from the phone
jack to the wall jack where your ISDN services are being delivered. Then you connect an Ethernet cable from your PC to the ISDN TA’s Ethernet jack. Older, less-capable TAs used an EIA/
TIA-232 serial port for PC connectivity. 

Wireless Access Points (WAPs)
A wireless access point (WAP) allows mobile users to connect to a wired network wirelessly via radio frequency technologies. WAPs also allow wired networks to connect to each other via wireless technologies. Essentially, they are the wireless equivalent of a hub or a switch in that they can connect multiple wireless (and often wired) devices together to form a network. 
    One of the most popular use for wireless access points is to provide Internet access in public areas, like libraries, coffee shops, hotels, and airports. WAPs are easy to set up; most often, you
just need to plug them in to a wired network and power them up to get them to work. Plus, without the clutter or added expense of cables to hook them up, they make ideal foundations for small business networks.

Note:

You’ll learn the intricate details of wireless access points that a Network+ technician should know in Chapter 6.

CSU/DSUs
The Channel Service Unit/Data Service Unit (CSU/DSU) is a common device found in equipment rooms when the network is connected via a T-series data connection or other digital serial technology (e.g., a T1 or Digital Data Server [DDS]). It is essentially two devices in one that are used  to connect a digital carrier (the T-series or DDS line) to your network equipment (usually to a router). The Channel Service Unit (CSU) terminates the line at the customer’s premises. It also provides diagnostics and remote testing, if necessary. The Data Service Unit (DSU) does the actual transmission of the signal through the CSU. It can also provide buffering and data flow control. Both components are required if you are going to connect to a digital transmission medium, such as a T1 line. Sometimes, however, one or both of these components may be built into a router. If both components are built into a router, you only have to plug the T1 line directly into the router. Otherwise, some Physical Layer specification, like V.35 or HSSI, will have to be used to cable the interface on the router to the external CSU/DSU.

Transceivers (Media Converters)
Another small device that is commonly seen on a network is the external transceiver (also known as a media converter). These are relatively simple devices that allow a NIC or other networking
device to connect to a different type of media than it was designed for. Many NICs have special connectors that will allow this, as do hubs and switches. For example, if you have a 100Base-TX switch and would like to connect it to another switch using fiber-optic cabling, you would connect a fiber transceiver to each switch’s transceiver port and then connect the two transceivers together with the appropriate fiber-optic cabling. With early Ethernet-style DB-15 female Digital-Intel-Xerox (DIX, or more commonly
Attachment Unit Interface [AUI]) NIC interfaces, which are still available as medium-independent connectors on more advanced NICs and other networking devices, an external transceiver
has to be used to convert the electrical signal from the device to one that is compatible with the cabling medium. Every other popular type of Ethernet technology, such as the xBase-T standards, has a built-in transceiver on the NIC card or device interface. An external transceiver is necessary with these technologies only to act as a media converter.

Firewalls
A firewall is probably the most important device on a network if that network is connected to the Internet. Its job is to protect LAN resources from attackers on the Internet. Similarly, it can prevent computers on the network from accessing various services on the Internet. It can be used to filter packets based on rules that the network administrator sets. These rules state what kinds of information can flow into and out of a network’s connection to the Internet. Firewalls can be either stand-alone “black boxes,” or can be set up in software on a server or router. Either way, the firewall will have at least two network connections: one to the Internet
(known as the “public” side), and one to the network (known as the “private” side). Sometimes, there is a third network port on a firewall. This port is used to connect servers and equipment that can be considered both public and private (like web and e-mail servers). This intermediary network is known as a demilitarized zone, or DMZ.


Firewalls are the first line of defense for an Internet-connected network. If a network was directly connected to the Internet without a firewall, an attacker could theoretically gain direct

access to the computers and servers on that network with little effort.

Read More

Gateways

Gateways
A gateway is any hardware and software combination that connects dissimilar network environments. Gateways are the most complex of network devices because they perform translations at multiple layers of the OSI model. For example, a gateway is the device that connects a LAN environment to a mainframe environment. The two environments are completely different. LAN environments use distributed processing, baseband communications, and the ASCII character set. Mainframe environments use centralized processing, broadband and baseband communications, and the EBCDIC character set. Each of the LAN protocols is translated to its mainframe counterpart by the gateway software. Another popular example is the e-mail gateway. Most LAN-based e-mail software, such as Novell’s GroupWise and Microsoft’s Exchange, can’t communicate directly with Internet mail servers without the use of a gateway. This gateway translates LAN-based mail messages into the SMTP format that Internet mail uses.

Example:

Gateways

Show More Than Click here

Read More

Router

Router
A router is a network device that connects multiple, often dissimilar, network segments into an internetwork. The router, once connected, can make intelligent decisions about how best to get network data to its destination based on network performance data that it gathers from the network itself. Routers are very complex devices. Often, routers are computers unto themselves with their
own complex operating systems to manage the routing functions (Cisco’s IOS, for example) and CPUs dedicated to the functions of routing packets. Because of their complexity, it is actually possible to configure routers to perform the functions of other types of network devices (like gateways, firewalls, etc.) by simply implementing the feature within the router’s software.

Example:

Router

Router Symbol

Show More Than Click here

Read More

Bridge

Bridge
A bridge, specifically a transparent bridge, is a network device that connects two similar network segments together. The primary function of a bridge is to keep traffic separated on both
sides of the bridge. Traffic is allowed to pass through the bridge only if the transmission is intended for a station on the opposite side. The main reasons for putting a bridge in a network
are to connect two segments together and to divide a busy network into two segments. A switch can be thought of as a hardware-based multiport bridge.

Example:

Bridge

Show More Than Click here

Read More

Switch

Switch
Like a hub, a switch connects multiple segments of a network together, with one important difference. Whereas a hub sends out anything it receives on one port to all the others, a switch recognizes frame boundaries and pays attention to the destination MAC address of the incoming frame as well as the port on which it was received. If the destination is known to be on a different
port than the port over which the frame was received, the switch will forward the frame out over only the port on which the destination exists. Otherwise, the frame is silently discarded.
If the location of the destination is unknown, then the switch acts much like a hub in  that it floods the frame out every port, except for the port over which it was received, unlike a hub. The only way any party not involved in that communication will receive the transmission is if it shares a port with the transmitter or receiver of the frame. This can occur if a hub is attached to the switch port, instead of in a 1:1 relationship of end devices and switch ports. The
benefit of a switch over a hub is that the switch increases performance because it is able to support full wire speed on each and every port with a nonblocking backplane, meaning the electronics inside the switch are at least equivalent in speed to the sum of the speeds of all ports.

Example:

Switch

Show More Than Click here

Read More

Hub

Hub
As you learned earlier, in a star topology Ethernet network, a hub is the device that connects all the segments of the network together. Every device in the network connects directly to the hub
through a single cable. Any transmission received on one port will be sent out all the other ports in the hub, including the receiving pair for the transmitting device, so that CSMA/CD on the transmitter can monitor for collisions. So, if one station sends it, all the others receive it; but based on addressing in the frame, only the intended recipient listens to it. This is to simulate the physical bus
that the CSMA/CD standard was based on. It’s why we call the use of a hub in an Ethernet environment a physical star/logical bus topology. It is important to note that hubs are nothing more
than glorified repeaters, which are incapable of recognizing frame boundaries and data structures; that’s why they act with such a lack of intelligence. A broadcast sent out by any device on the hub
will be propagated to all devices connected to the hub. Any two or more devices connected to the hub have the capablity of causing a collision with each other, just as in the case of a physical bus.

Example:

Hub

Show More Than Click here

Read More

The network interface card (NIC)

NIC
The network interface card (NIC), as its name suggests, is the expansion card you install in your computer to connect, or interface, your computer to the network. This device provides the physical, electrical, and electronic connections to the network media. A NIC is either an expansion card (the most popular implementation) or built in to the motherboard of the computer. In most cases, a NIC connects to the computer through expansion slots, which are special slots located on a computer’s motherboard that allow peripherals to be plugged direclty into it. In some notebook computers, NIC adapters can be connected to the printer port or through a PC card slot. NIC cards generally all have one or two light emitting diodes (LEDs) that help in diagnosing
problems with their functionality. If there are two separate LEDs, one of them may be the Link LED, which illuminates when proper connectivity to an active network is detected. This often means that the NIC is receiving a proper signal from the hub/MAU or switch, but it could indicate connectivity to and detection of a carrier on a coax segment or connectivity with a router or other end device using a crossover cable. The other most popular LED is the Activity LED. The Activity LED will tend to flicker, indicating the intermittent transmission or receipt of frames to or from the network.

Example:

NIC PCI

Show More Than Click here



Note:

The first LED you should verify is the Link LED because if it’s not illuminated, there will be no chance for the Activity LED to illuminate.

Read More

Common Network Connectivity Devices

Common Network Connectivity Devices
Now that you are familiar with the various types of network media and connections, you should learn about some devices commonly found on today’s networks. Because these devices connect
network entities, they are known as connectivity devices:

• The network interface card (NIC)
• The hub
• The switch
• The bridge
• The router
• The gateway
• Other devices

Note:

These will be discussed in more detail in Chapter 2, “The OSI Model.”

Read More

Cable Type Summary

Cable Type Summary
       Table 1.2 summarizes the cable types.

TABLE 1 . 2 Common Ethernet and FDDI Cable Types

Read More

Fiber-Optic Cable

Fiber-Optic Cable
Because fiber-optic cable transmits digital signals using light impulses rather than electricity, it is immune to Electromagnetic Interference (EMI) and Radio Frequency Interference (RFI).

FIGURE 1 . 1 7 A USB plug

Note:

You will find a complete discussion of these terms in Chapter 6, but you should
know at this point that both could affect network performance.
Anyone who has seen UTP cable for a network run down an elevator shaft would, without
doubt, appreciate this feature of fiber. Light is carried on either a glass or a plastic core. Glass
can carry the signal a greater distance, but plastic costs less. Regardless of which core is used,
the core is surrounded by a glass or plastic cladding, which is more glass or plastic with a different index of refraction that refracts the light back into the core. Around this is a layer of flexible plastic buffer. This can be then wrapped in an armor coating (where necessary), typically Kevlar, and then sheathed in PVC or plenum.

Note: 

For more information about fiber-optic cabling, see Cabling: The Complete
Guide to Network Wiring, Third Edition, by David Barnett, David Groth, and Jim
McBee (Sybex, 2004).

The cable itself comes in two different styles: single-mode fiber (SMF) and multimode fiber (MMF). The difference between single-mode fibers and multimode fibers is in the number of light rays (and thus the number of signals) they can carry. Generally speaking, multimode fiber is used for shorter-distance applications and single-mode fiber for longer distances. If you happen to come across a strand of fiber in the field and want to know if it’s single mode
or multimode, here are some general guidelines. First of all, if it’s got a yellow jacket, it’s probably single mode. If it’s got an orange jacket, it’s most likely multimode. Also, check the writing
on the cable itself. You’ll find a number like 62.5/125. These are the outside diameters of the core and the cladding (respectively). If the first number is a 8, 9, or 10, it is most likely a single mode. On the other hand, if the numbers read as before (62.5/125), it’s most likely a multimode strand of fiber. Use these two tips to help you identify that errant strand of fiber. Although fiber-optic cable may sound like the solution to many problems, it has pros and
cons just as the other cable types. Here are the pros:

• Is completely immune to EMI or RFI
• Can transmit up to 40 kilometers (about 25 miles)

Here are the cons of fiber-optic cable:

• Is difficult to install
• Requires a bigger investment in installation and materials

Fiber-Optic Connectors

Fiber-optic cables can use a myriad different connectors, but the two most popular and recognizable are the straight tip (ST) and subscriber (or square) connector (SC) connectors. The ST

fiber-optic connector, developed by AT&T, was one of the most widely used fiber-optic connectors. It uses a BNC attachment mechanism similar to the Thinnet connection mechanism,

which makes connections and disconnections relatively easy. Its ease of use is one of the attributes that makes this connector so popular. Figure 1.18 shows an example of an ST connector.

Notice the BNC attachment mechanism. The SC connector (sometimes known also as a square connector) is another type of fiber-optic connector. As you can see in Figure 1.19, SC connectors are latched connectors. This latching mechanism holds the connector in securely while in use and prevents it from just falling out.

Note:

If data runs are measured in kilometers, fiber optic is your cable of choice
because copper cannot reach more than 500 meters (about 1500 feet) without
electronics regenerating the signal, and that’s for the all-but-obsolete 10Base5
coaxial standard. The standards limit UTP to a mere 100 meters. You may also
want to opt for fiber-optic cable if an installation requires high security, because
it does not create a readable magnetic field. Although fiber-optic technology
was initially very expensive and difficult to work with, it is now being used in
some interesting places, such as Gigabit or 10GB Internet backbones. Ethernet
running at 10Mbps over fiber-optic cable to the desktop is designated 10Base-
FL; the 100Mbps version of this implementation is 100Base-FX. The L in the
10Mbps version stands for link, as opposed to such other designations as B for
backbone and P for passive.

SC connectors work with either single-mode or multimode optical fibers, and they will last for around 1000 matings. They are seeing increased use but aren’t as popular as ST connectors for LAN connections.

FIGURE 1 . 1 8 An example of an ST connector

FIGURE 1 . 1 9 A sample SC connector

Small Form Factor Fiber-Optic Connectors
One of the more popular styles of fiber-optic connectors is the small form factor (SFF) style of connector. SFF connectors allow more fiber-optic terminations in the same amount of space over their
standard-sized counterparts. The two most popular are the mechanical transfer registered jack (MT-RJ or MTRJ), designed by AMP, and the Local Connector (LC), designed by Lucent.
MT-RJ The MT-RJ fiber-optic connector was the first small form factor fiber-optic connector to see widespread use. It is one-third the size of the SC and ST connectors it most often replaces. It had
the following benefits:

•  Small size
• TX and RX strands in one connector
• Keyed for single polarity
• Pre-terminated ends that require no polishing or epoxy
• Easy to use

Figure 1.20 shows an example of an MT-RJ fiber-optic connector

FIGURE 1 . 2 0 A sample MT-RJ fiber-optic connector

LC
Local Connector is a newer style of SFF fiber-optic connector that is overtaking MT-RJ as a fiber-optic connector. It is especially popular for use with Fibre Channel adapters and Gigabit
Ethernet adapters. It has similar advantages to MT-RJ and other SFF-type connectors but is easier to terminate. It uses a ceramic insert as standard-sized fiber-optic connectors do. Figure 1.21
shows an example of the LC connector.

FIGURE 1 . 2 1 A sample LC fiber-optic connector

Read More

Twisted-Pair Cable

Twisted-Pair Cable

Twisted-pair cable consists of multiple, individually insulated wires that are twisted together in pairs. Sometimes a metallic shield is placed around the twisted pairs. Hence, the name shielded
twisted-pair (STP). (You might see this type of cabling in Token Ring installations.) More commonly, you see cable without outer shielding; it’s called unshielded twisted-pair (UTP). UTP is
commonly used in twisted-pair Ethernet (10Base-T, 100Base-TX, etc.), star-wired networks. Let’s take a look at why the wires in this cable type are twisted. When electromagnetic signals are conducted on copper wires that are in close proximity (such as inside a cable), some electromagnetic interference occurs. In this scenario, this interference is called crosstalk. Twisting two wires together as a pair minimizes such interference and also provides some protection
against interference from outside sources. This cable type is the most common today. It is popular for several reasons:

• It’s cheaper than other types of cabling.
• It’s easy to work with.
• It permits transmission rates considered impossible 10 years ago. 

    UTP cable is rated in the following categories:

Category 1 Two twisted wire pairs (four wires). Voice grade (not rated for data communications). The oldest UTP. Frequently referred to as POTS, or plain old telephone service. Before
1983, this was the standard cable used throughout the North American telephone system. POTS cable still exists in parts of the Public Switched Telephone Network (PSTN). Supports signals
limited to a frequency of 1MHz. Category 2 Four twisted wire pairs (eight wires). Suitable for up to 4Mbps, with a frequency
limitation of 10MHz. Category 3 Four twisted wire pairs (eight wires) with three twists per foot. Acceptable for transmissions up to 16MHz. A popular cable choice since the mid-1980s, but now limited mainly to telecommunication equipment.

Category 4 Four twisted wire pairs (eight wires) and rated for 20MHz. 

Category 5 Four twisted wire pairs (eight wires) and rated for 100MHz .

Category 5e Four twisted wire pairs (eight wires) and rated for 100MHz, but capable of handling the disturbance on each pair caused by transmitting on all four pairs at the same time, which is needed for Gigabit Ethernet.

Category 6 Four twisted wire pairs (eight wires) and rated for 250MHz. Became a standard in June 2002. 

Note:

Frequently, you will hear Category shortened to Cat. Today, any cable that you
install should be a minimum of Cat 5e. This is a minimum because some cable is now certified to carry a bandwidth signal of 350MHz or beyond. This allows unshielded twisted-pair cables to exceed speeds of 1Gbps, which is fast enough to carry broadcast-quality video over a network. A common saying is that there are three ways to do things: the Right way, the Wrong way, and the IBM way. IBM uses types instead of categories when referring to TP (twistedpair) cabling specifications. Even though a cabling type may seem to correspond
to a cabling category (such as Type 1 and Category 1), the two are not the same; IBM defines its own specifications.

 Now that you’ve learned the different types of UTP cables, you will learn how best to connect them to the various pieces of networking equipment using UTP.

*Real World Scenario*

Category 5e Cabling Tips

If you expect data rates faster than 10Mbps over UTP, you should ensure that all components are rated to the category you want to achieve and be very careful when handling all components.
For example, pulling too hard on Cat 5e cable will stretch the number of twists inside the jacket, rendering the Cat 5e label on the outside of the cable invalid. Also, be certain to connect
and test all four pairs of wire. Although today’s wiring usually uses only two pairs, or four wires, the standard for Gigabit Ethernet over UTP requires that all four pairs, or eight wires, be in good condition.
You should also be aware that a true Cat 5e cabling system uses rated components from end to end, patch cables from workstation to wall panel, cable from wall panel to patch panel, and patch cables from patch panel to hub. If any components are missing or if the lengths do not match the Category 5e specification, you don’t have a Category 5e cabling installation. Also, installers should certify that the entire installation is Category 5e compliant. However, this requires very expensive test equipment that can make the appropriate measurements.

Connecting UTP
Clearly, a BNC connector won’t fit easily on UTP cable, so you need to use an RJ (Registered Jack) connector. You are probably familiar with RJ connectors. Most telephones connect with an RJ-11 connector. The connector used with UTP cable is called RJ-45. The RJ-11 has four wires, or two pairs, and the network connector RJ-45 (also known as an 8P8C connector when referring to the plug instead of the jack) has four pairs, or eight wires, as shown in Figure 1.13.

Exmple:

FIGURE 1 . 1 3 RJ-11 and RJ-45 connectors

       In almost every case, UTP uses RJ connectors. Even the now-extinct ARCnet used RJ connectors. You use a crimper to attach an RJ connector to a cable, just as you use a crimper with the BNC connector. The only difference is that the die that holds the connector is a different shape. Higher-quality crimping tools have interchangeable dies for both types of cables.


Signaling Methods
The amount of a cable’s available bandwidth (overall capacity, such as 10Mbps) that is used by each signal depends on whether the signaling method is baseband or broadband. With baseband, the entire bandwidth of the cable is used for each signal (using one channel). It is typically used with digital signaling. With broadband, on the other hand, the available bandwidth is divided into descrete bands. Multiple signals can then be transmitted within these different bands. Some form of tuning device, or demodulator, is required to choose the specific frequency of interest, as opposed to baseband receiving circuitry, which can be hardwired to a specific frequency. Don’t confuse this broadband with the term that is the opposite of narrowband, which is any bit rate of T1 speeds (1.544Mbps) or slower. That broadband refers to speeds in excess
of T1/E1 rates, such as Broadband-ISDN (B-ISDN), which has been developed under the ATM specifications.

Ethernet Cable Descriptions
Ethernet cable types are described using a code that follows this format: N<Signaling>-X. Generally speaking, N is the signaling rate in megabits per second, and <Signaling> is the signaling type, which is either base or broad (baseband or broadband). X is a unique identifier for a specific Ethernet cabling scheme.

Let’s use a generic example: 10BaseX. The two-digit number 10 indicates that the transmission speed is 10Mb, or 10 megabits. The value X can have different meanings. For example, the
5 in 10Base5 indicates the maximum distance that the signal can travel—500 meters. The 2 in 10Base2 is used the same way, but fudges the truth. The real limitation is 185 meters. Only the
IEEE committee knows for sure what this was about. We can only guess that it’s because 10Base2 seems easier to say than 10Base1.85.

    Another 10Base standard is 10Base-T. The T is short for twisted-pair. This is the standard for running 10-Megabit Ethernet over two pairs (four wires) of Category 4, 5e, or 6 UTP. The fourth, and currently final, 10Base is 10Base-FL. The F is short for fiber, while the L stands for link. 10Base-FL is the standard for running 10-Megabit Ethernet over fiber-optic cable to the desktop. Table 1.2, shown a bit later, summarizes this data.
 Similarly, there are also standards for 100Base, 1000Base, and 10GBase cabling. Let’s take

A closer look at these standards:
100Base-TX As network applications increased in complexity, so did their bandwidth requirements. Ten-megabit technologies were too slow. Businesses were clamoring for a higher
speed standard so that their data could be transmitted at an acceptable rate of speed. A 100- megabit standard was needed. Thus the 100Base-TX standard was developed.

The 100Base-TX standard is a standard for Ethernet transmission at a data rate of 100Mbps. This Ethernet standard is also known as Fast Ethernet. It uses two UTP pairs (four wires) in a minimum of Category 5 UTP cable.

1000Base-TX 1000Base-TX, most commonly known as Gigabit Ethernet, allows 1000Mbps throughput on standard twisted-pair, copper cable (rated at Category 5e or higher).

1000Base-SX The implementation of Gigabit Ethernet running over multimode fiber-optic cable (instead of copper, twisted-pair cable) and using short wavelength laser.

1000Base-LX The implementation of Gigabit Ethernet over single-mode and multimode fiber using long wavelength laser.

1000Base-CX An implementation of Gigabit Ethernet over balanced, 150ohm copper cabling and uses a special 9-pin connector known as the High Speed Serial Data Connector (HSSDC).

10GBase-SR An implementation of 10 Gigabit Ethernet that uses short wavelength lasers at 850 nanometers(nm) over multimode fiber. It has a maximum transmission distance of between
2 and 300 meters, depending on the size and quality of the fiber.

10GBase-LR An implementation of 10 Gigabit Ethernet that uses long wavelength lasers at 1310 nm over single-mode fiber. It also has a maximum transmission distance between 2 meters and 10 kilometers, depending on the size and quality of the fiber.

10GBase-ER An implementation of 10 Gigabit Ethernet running over single-mode fiber. It uses extra long wavelength lasers at 1550 nm. It has the longest transmission distances possible of the 10-Gigabit technologies: anywhere from 2 meters up to 40 kilometers, depending on the size and quality of the fiber used.

Note:

See the upcoming section, “Fiber-Optic Cable,” in this chapter, for more information
on single-mode and multimode fiber and on fiber in general.

IEEE Standard 1394 (FireWire)
One unique cabling type that is used in a limited sense is IEEE standard 1394, more commonly known as FireWire (or as Sony calls it, i.Link). Developed by Apple Computer, FireWire runs
at 100, 200, 400Mbps (800Mbps in the 1394b standard), but in its standard mode it has a cable length limitation of 15 feet (4.5 meters), which limits it to specialized applications like data
transfer between two computers located in close proximity or data transfer between a computer and another device (like an MP3 player). 

FireWire uses two types of connectors: the 6 pin and the 4 pin. The 6-pin connector (as shown in Figure 1.14) is for devices that need to be powered from the computer. FireWire cables with the 6-pin connector contain two pairs (four conductors) of copper wire for carrying data and one pair for powering devices, all within a common, braided metal shield. Cables using the 4-pin connector (Figure 1.15) are for data transfer only, and they contain only the four conductors for data, none for power.

Example:

FIGURE 1 . 1 4 Six-pin FireWire connector (male)

Example:

FIGURE 1 . 1 5 Four-pin FireWire connector (male)

Note:

More information about FireWire and its associated standards can be found at
the 1394 Trade Association website at www.1394ta.org.

Universal Serial Bus (USB)
Over the past few years, computer peripherals have been moving away from parallel or serial connection and to a new type of bus. That bus is the Universal Serial Bus (USB). The built-in serial bus of most motherboards generally offers a maximum of 2 external interfaces for connectivity to a PC, although add-on adapters can take that count up to as many as 16 serial interfaces. USB, on the other hand, can connect a maximum of 127 external devices. Also, USB is a much more flexible peripheral bus than either serial or parallel. USB supports connections to printers, scanners, and many other input devices (such as keyboards, joysticks, and mice). 

     When connecting USB peripherals, you must connect them either directly to one of the USB ports (as shown in Figure 1.16) on the PC or to a USB hub that is connected to one of those USB ports. Hubs can be chained together to provide multiple USB connections. Although you can connect up to 127 devices (each device has a USB plug, as shown in Figure 1.17), it is impractical in reality. Most computers with USB interfaces will support around 12 USB devices.

Example:

FIGURE 1 . 1 6 A USB port

Read More